API 5L vs ASTM A106 seamless pipe: which standard should you specify?

Seamless pipe is ordered against two standards that look interchangeable and are not. API 5L governs line pipe for oil and gas transmission; ASTM A106 governs pressure piping and general structural service. They differ in permitted grades, in what the test certificate actually proves, and in how the pipe is marked. Specifying the wrong one is one of the most common reasons an inspection agency rejects a shipment on arrival.

What each standard actually governs

API 5L and ASTM A106 cover overlapping territory but were written for entirely different service environments. API 5L — Specification for Line Pipe — was developed by the American Petroleum Institute for use in oil and gas transmission systems. ASTM A106 — Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service — was developed for power plant and general industrial piping.

The distinction matters less than it may appear, because most Chinese mills produce A106 Grade B material on the same rolling and heat-treatment lines used for API 5L PSL2. The practical difference is therefore not in the steel but in the documentary package, and that is where shipments get rejected: an inspection agency asked to verify API 5L PSL2 will look for Charpy impact results, and if the only certificate is an A106 certificate those results simply do not exist.

Grade and specification comparison

The grades that come up most often in order correspondence:

Specification Available grades Size range Typical application Specification level
API 5L Grade BX52, X56, X60, X65, X70, X80≤ 24 inLine pipe — oil & gas transmission, water pipelinesPSL1 / PSL2
API 5L Grade AX42, X46, X52 (legacy)≤ 24 inLine pipe — lower strength, used for less severe servicePSL1 / PSL2
ASTM A106 Grade AClass A — equivalent to API 5L BNPS 1/8–36 inPressure piping, general service, boiler tubes—
ASTM A106 Grade BClass B — the standard commercial gradeNPS 1/8–36 inPressure piping, structural, mechanical—
ASTM A106 Grade CClass C — higher yield, lower availabilityNPS 1/8–36 inHigher temperature or pressure service—

Two points worth flagging. First, the PSL2 designation is the one that decides the commercial outcome — not the grade. Two orders both saying "X52" can carry completely different price and inspection consequences depending on whether PSL1 or PSL2 is written underneath. Second, for a line pipe project, X52 is the entry grade that most Chinese mills quote comfortably; X60 and above require confirmable rolling capacity and are priced differently.

What each standard requires you to test

This table is the difference that shows up at the inspection gate. It is worth printing and attaching to the purchase order, because it removes the most common source of dispute:

Requirement API 5L PSL1 API 5L PSL2 ASTM A106
Chemical analysisRequiredRequiredRequired
Tensile test on each heatRequiredRequiredRequired
Hydrostatic testOptional (PSL1) / required (PSL2)OptionalOptional
Eddy current or UTPSL2 or as specifiedOptionalOptional
Charpy impact testRequired (PSL2, supplementary)Not required by A106Not required
NDE (RT / UT)As specified or supplementaryAs specifiedAs specified
Traceability to heat numberRequired — heat number stamped on pipeRequired — heat number stamped on pipeRequired — heat number stamped on pipe

Note the two rows that catch experienced buyers out. Hydrostatic testing is optional under A106 but effectively mandatory under PSL2, and a PSL2 order where the certificate shows no hydrostatic test has been rejected at destination. Charpy impact testing is the single most frequently missing item on PSL2 shipments that were produced to a PSL1 documentation standard.

Which standard to specify, by project type

As a rule of thumb for the markets we ship into:

  • Oil and gas transmission, gathering lines, cross-country pipelines — API 5L PSL2. If sour or offshore service, add Charpy impact at design temperature and the API sour service supplementary requirements.
  • Water pipelines and district heating — API 5L is common in international contracts for anything above DN 600; ASTM A106 Grade B is accepted where pressure is moderate and the specification allows it.
  • Power plant boiler and steam lines — ASME SA-106, which is the ASME listing of ASTM A106. ASME material must come from an ASME-listed mill with full certification.
  • General structural and mechanical fabrication — ASTM A106 Grade B, which is the lowest-cost commercially available grade and is what most distributors stock.
  • Hydrogen, sour or high-chloride service — API 5L PSL2 with supplementary requirements, and confirm the material is not susceptible to hydrogen embrittlement for the specified strength level.

If you are not certain which applies, write both and require the mill to confirm which standard it is quoting against before production. A mill that answers this question in one email is a mill that will deliver the right documentation; a mill that cannot answer it is a mill that will leave your inspection agency to discover the problem at the port.

Pipe marking and traceability

Every length should be traceable by heat number back to the mill certificate. At minimum the marking must carry the manufacturer mark, the grade, the heat number and the standard designation. If the material is API 5L with the monogram, the licence number must also appear. During unloading, spot-check ten lengths against the mill certificate list and confirm the heat numbers match. A mismatch is normal in an ordinary yard and serious in an API project.

We supply each shipment with loading photographs and video, and can arrange third-party inspection at SGS, BV, CCIC or Intertek before loading on request. Photographs alone do not replace a certificate, but they settle the question of whether the cargo was handled correctly in transit.

Certificate type and third-party inspection

EN 10204 type 3.1 is a declaration by the manufacturer. Type 3.2 is a declaration independently verified by a third-party inspection body. For API 5L PSL2 material destined for a pipeline operator, specify 3.2 by name of the inspection body — naming the body removes the possibility of a certificate being issued by an inspector the operator has not approved. See our guide on how to read a mill test certificate for what to check on arrival.

Frequently asked questions

Is API 5L Grade B the same as ASTM A106 Grade B?

In mechanical properties and nominal dimensions they are effectively equivalent for the common wall thickness range, and mills routinely supply A106 Gr.B to an API 5L PSL2 line pipe specification. They are not the same document, however. API 5L carries mandatory Charpy impact requirements under PSL2, defined weld procedure qualification requirements, and an API monogram licence, none of which A106 requires. A project specification written in A106 does not entitle you to a PSL2 certificate, and an inspector checking against API 5L will reject an A106 certificate.

What is the difference between API 5L PSL1 and PSL2?

PSL1 is the lower specification level: it requires the chemical analysis, tensile test and hardness test, plus the dimensional and marking control, but the hydrostatic test may be waived and impact testing is optional. PSL2 adds mandatory Charpy impact testing at the specified temperature, mandatory hydrostatic testing or an agreed substitute NDE method, and tighter control of weld procedures and traceability. For any service where a failure would be catastrophic — sour service, offshore, high-pressure gas — PSL2 is effectively mandatory in practice, and many buyers specify PSL2 even where PSL1 would technically be accepted.

Which standard should I specify for a power plant project?

For boiler and steam service, ASME SA-106 (the ASME designation of ASTM A106) is normally the correct reference because ASME requires the material to be listed and traceable within an ASME quality management system. For water and general process piping at moderate pressure, ASTM A106 Grade B is the normal commercial choice. For hydrogen, sour or offshore service, specify API 5L PSL2 and add the supplementary requirements — notably Charpy impact at the design minimum temperature and, where H2S is present, the sour service provisions of API 5L.

What does the pipe marking have to show?

API 5L requires the following to be marked on each length: the manufacturer name or mark, the applicable standard and specification order, the grade, the outside diameter, the wall thickness, the heat number, the production date and the licence number of the API monogram. ASTM A106 requires the manufacturer name or mark, the grade, the heat number, the specification designation and the last four digits of the heat number under the governing specification. In practice the marking is the fastest way to identify a non-conforming delivery before it is unloaded.

Can I order API 5L pipe with an EN 10204 3.2 certificate?

Yes, and for most imported contracts it is worth doing. A 3.2 certificate is issued by an independent inspection body that has witnessed the material tests, which removes any argument about whether the mill's own laboratory results are accepted. Confirm the inspection body by name in the purchase order and confirm it is an accredited member of a recognised third-party inspection scheme. A 3.1 certificate is a mill declaration only and is not independent.

What pipe end preparation do I need for API 5L?

API 5L PSL2 pipe is normally supplied with beveled ends suitable for welding, to a bevel angle of 60° with a root face of 1.6 mm to 3.2 mm unless otherwise agreed. A106 pipe can be supplied plain or beveled and the requirement is stated on the order. If the pipe will be field-welded without beveling, specify the end condition explicitly — bevelled ends are not free, and the difference shows up on the invoice.

Need help specifying your material?

Send grade, thickness, width, coating and quantity. We confirm mill availability and return a proforma with the applicable standard and delivery window — normally within one business day.

Request a Quote