G60 vs G90 galvanized steel coil: which coating weight should you specify?

Buyers who write "G90" in a purchase order usually know the answer they want. The problem is that G and Z designations are frequently confused, and a 25% difference in zinc coating weight is the difference between a roof that lasts 12 years and one that lasts 25. This guide sets out exactly what each grade means, how to convert between systems, and which environments each grade is actually suitable for.

What the G and Z designations actually mean

Both systems describe the same thing — the total zinc coating weight on both faces of the coil — but they express it in different units and sit under different standards.

G is the ASTM A653 system, quoted in ounces per square foot (total, both sides). Z is the EN 10346 system, quoted in grams per square metre (total, both sides). The conversion is 1 oz/ft² ≈ 305 g/m², so the two describe the same coating once you translate the unit.

One point catches people out: the number is a total across both sides, not a per-side figure. A coil quoted as G90 / Z275 carries 275 g/m² in total, so 137.5 g/m² on each face. If you need a guaranteed minimum on a specific face, you have to say so explicitly on the order — because the mill is otherwise free to distribute the coating slightly unevenly between the two faces.

Converting coating weight to micron thickness

Coating weight is a mass. Coating thickness is what actually resists corrosion, and it is what a fabricator thinks in. The conversion comes from the density of zinc at 7.14 g/cm³:

Thickness (µm per side) = (Coating weight g/m² ÷ 2) × 0.14 Divide by two first because the quoted weight is for both sides. The 0.14 constant is derived from the zinc density of 7.14 g/cm³.

Worked through for G90 / Z275: 275 ÷ 2 = 137.5 g/m² per side, and 137.5 × 0.14 = 19.3 µm per side. For G60 / Z180 the same calculation gives 90 × 0.14 = 12.6 µm per side. That is roughly a 53% difference in film thickness, which is why the corrosion life gap is so much wider than the numbers suggest.

Full coating weight reference table

Coating weight on both sides, equivalent single-side thickness, and the ASTM and EN designations that map to each other:

Coating weight (g/m², both sides)Thickness per side (µm)ASTM A653EN 10346Salt spray to red rustTypical environment
604.2G30Z060200–400Indoor, dry, warehouse, appliance housings
805.6—Z080300–500Dry inland, light framing, interior use
1007.0G40Z100400–600Indoor and sheltered, HVAC ducting
1208.4—Z120500–700Mild inland, sheds, fencing
1409.8G50Z140600–1000Moderate humidity, industrial areas
18012.6G60Z1801000–1500High-humidity coastal, chemical plant surrounds
27519.3G90Z2751500–2500Marine, heavy industrial, salt spray regions
35024.5G115Z3502000–3000Severe coastal, offshore, chemical processing
45031.5G140–G165Z4502500–4000Offshore platforms, extreme industrial exposure
60042.0G185–G210Z6003500–5000Marine splash zone, high-chloride industrial sites

Salt spray figures are ASTM B117 neutral salt spray hours to first red rust. Treat them as a relative ranking between coatings rather than a prediction of field life — real performance depends on the environment and on whether the coating is intact when it is installed.

Choosing by corrosion environment

The right way to select a coating weight is to classify the site first and let the environment choose the grade. ISO 9223 does this with five corrosivity categories, from C1 very dry indoor to C5 marine and offshore.

ISO 9223 categoryEnvironmentCorrosivityZinc loss rateTypical specificationWhere it is used
C1Dry indoorVery low—G30–G40 / Z060–Z100Interiors, air-conditioned buildings
C2Rural / urban inlandLow—G60–G90 / Z180–Z275Sheds, farm buildings, wall cladding
C3Urban / moderately humidMedium0.2–0.6 µm/yrG90–G115 / Z275–Z350Commercial buildings, industrial roofing
C4Coastal, industrial, urban trafficHigh0.6–1.5 µm/yrG115–G185 / Z350–Z600Coastal structures, chemical plants
C5Marine, offshore, high salinityVery high1.5–3.0 µm/yrG185+ / Z600 or higherOffshore platforms, marine terminals

G60 against G90, side by side

G60 / Z180 and G90 / Z275 are the two grades you will be asked to compare most often, and the decision usually comes down to exposure and design life rather than price alone.

PropertyG60 / Z180G90 / Z275
Coating weight, both sides180 g/m²275 g/m²
Thickness per side12.6 µm19.3 µm
Relative zinc massBaseline53% more
Neutral salt spray to red rust1000–1500 hours1500–2500 hours
ISO 9223 category suited toC2, some C3C3, some C4
Typical service life10–20 years20–35 years
Forming and weldingSimpler — softer zinc, less burn-through riskNeeds more care — thicker zinc needs controlled welding current and edge sealing
Best suited toInterior framing, HVAC ducting, sheltered cladding, shedsStandard roofing, wall cladding, purlins, C and Z sections, industrial buildings

If in doubt, G90 / Z275 is the default for general outdoor construction — it is the most widely specified coating weight in the world for a reason. Step up to G115 or higher only where the environment genuinely demands it, because the thicker zinc does affect forming behaviour, welding procedure and cut-edge sealing requirements.

How to write the specification correctly

A specification line that removes all ambiguity looks like this:

Material: ASTM A653 CS Type B, coating G90 (equivalent Z275), total coating weight 275 g/m² minimum on both sides, non-spangled, chromate-free passivated and oiled
Thickness: 0.50 mm base metal, tolerance per ASTM A653
Coil weight: to suit our uncoiler (state the maximum weight and the ID you run)
Finish: to be painted — confirm passivation type with the mill Stating the standard, the minimum total coating weight, the surface condition and the coil dimensions together removes the three arguments that most often delay a shipment.

Three details in that line are worth keeping. First, "minimum 275 g/m² total on both sides" removes the ±10% tolerance ambiguity that ASTM A653 permits on delivered weight. Second, non-spangled matters if the coil is to be painted or roll-formed, because the zinc crystal pattern will otherwise telegraph through the finish. Third, always specify the coil weight and inner diameter to match the buyer's uncoiler — it is the single most effective way to avoid a coil that arrives and cannot be processed.

Frequently asked questions

Is G90 the same as Z275?

Yes. G90 is the ASTM A653 designation (0.90 oz/ft² total on both sides) and Z275 is the equivalent EN 10346 designation (275 g/m² total). Both describe the same coating mass on the same product. You will see both on the same specification sheet depending on which standard the mill quotes against.

How do I convert coating weight to micron thickness?

Thickness in microns per side equals the per-side coating weight in g/m² multiplied by 0.14. The constant comes from the density of zinc at 7.14 g/cm³. Since coating weight is always quoted as a total across both sides, divide by two first. So G90 (275 g/m² total) is 137.5 g/m² per side, which works out to about 19.3 microns per side.

How much more zinc does G90 carry than G60?

G90 carries 275 g/m² against G60 at 180 g/m², so 53% more zinc by mass. On the converted per-side film thickness that is 19.3 microns against 12.6 microns. The practical effect is a materially longer time to first red rust — typically 1500–2500 hours in neutral salt spray for G90 against 1000–1500 hours for G60.

Is G90 enough for a coastal project?

For a coastal site more than a few hundred metres from the shoreline, G90 (Z275) is the usual specification and performs well. Within direct marine exposure or salt spray, specify G185 (Z600) or a pre-painted system with a PVDF top coat, and seal cut edges with zinc-rich paint after fabrication. If the project is genuinely marine, discuss a zinc-aluminium-magnesium (ZAM) coating with the mill instead.

What is the tolerance on coating weight?

ASTM A653 permits a tolerance of ±10% on the total coating weight as delivered. This is worth knowing if you are specifying a minimum: always state the minimum total coating weight on both sides rather than relying on the nominal value, and check the actual figure on the mill test certificate when the shipment is weighed.

Can G90 be painted over?

Yes, and it is frequently supplied passivated and oiled specifically so it can be painted or roll-formed downstream. Specify passivation and oil if the coil is going into a paint line, and confirm the passivation type — chrome-free is now the norm for European-bound material.

Need help specifying your material?

Send grade, thickness, width, coating and quantity. We confirm mill availability and return a proforma with the applicable standard and delivery window — normally within one business day.

Request a Quote