The right roofing sheet for a project in Riyadh is not the right sheet for a project in Manila, and the right sheet for neither may be the right sheet for Mombasa. This guide compares the four practical options against the four conditions that actually destroy roofing sheet: UV exposure, salt spray, high humidity with poor ventilation, and long-span structural requirements.
Roofing sheet fails for one of four reasons — ultraviolet exposure, salt, standing moisture, or the base metal simply being too thin for the wind load. Which of those dominates depends on where the building is, and it changes the specification completely. Here is the mapping we work to:
| Climate zone and examples |
Conditions | Recommended sheet | Premium option | Typical service life | The thing that actually causes failure |
|---|---|---|---|---|---|
| Hot-humid tropical SE Asia, Central America | Constant high humidity, heavy rain, moderate UV | Galvalume AZ150 with HDP 32 µm, or GI Z275 with HDP 32 µm | Aluminium 0.5–0.6 mm for coastal and island exposure | 25+ years | Ensure the reverse face is passivated and oiled — moisture trapped against the underside causes red rust within two seasons |
| Hot-arid desert Middle East, North Africa | Extreme UV, extreme daytime heat, little rain, large diurnal swing | GI Z275 with PVDF 35 µm, light colours preferred | Aluminium 0.5 mm where a long unpainted life is required | 20–25 years | Dark colours reach surface temperatures high enough to accelerate coating ageing — specify light RAL for desert roofs |
| Coastal / marine Middle East, Africa, SE Asia islands | Chloride deposition, salt spray, near-constant humidity | GL AZ150 with HDP 32 µm minimum, or PVDF 35 µm | Aluminium 0.5–0.7 mm — the only coating-free option that lasts | 20–25 years | Salt-laden air attacks the base at every cut edge and fastener hole — specify cut-edge protection and stainless fixings |
| Temperate / rainy Southern Europe, Turkey, South Africa | Moderate corrosion, high rainfall, seasonal temperature swing | GI Z275 with PE 20 µm or HDP 25 µm | Galvalume AZ150 with PE 20 µm | 15–20 years | The standard case — G60 with PE is adequate, and there is no reason to over-specify here |
| Industrial / high heat Refineries, power plant, warehouses | Chemical exposure, high ambient temperature, process heat | GI Z275 or Z350 with HDP 32 µm | Aluminium for severe process areas | 15–25 years | Specify the coating system against the actual process exposure, not the ambient climate |
Read across the table and the pattern is clear: base metal handles corrosion, coating handles appearance and UV, and gauge handles structure. Most failures come from a buyer specifying a good coating on a base that does not suit the environment, or specifying a heavy gauge with a thin coating.
Two practical rules follow from this. First, in coastal and humid environments, the base metal decision dominates — galvalume or aluminium, not galvanized. Second, in hot-arid environments, the coating system and colour dominate, and the base metal choice matters much less. For the detail on coating weights, see G60 versus G90; for the coating systems themselves, see the PPGI paint build-up guide.
The gauge is a structural decision, and it is set by span, design wind load and the local building code — not by the product category. 0.47 mm to 0.60 mm covers most profiled roofing across our export markets. But note the trade-off explicitly: doubling the gauge does not double the service life. A 0.5 mm sheet with a proper 32 µm coating system will consistently outlast a 0.6 mm sheet with a 20 µm PE coating, because the coating is what stops the corrosion. Where the budget forces a thinner coating, reduce the gauge expectation rather than the coating spec.
Dark colours raise roof surface temperature significantly. In direct desert sun a dark surface can exceed 70°C, and service life is a function of temperature as well as UV radiation. This is why light RAL colours are standard practice for desert projects and why some project specifications explicitly require a solar reflectance index. If the building has air conditioning underneath, the difference is directly measurable in running cost as well as in coating life.
Two details cause more premature failures than the sheet itself. First, galvanic compatibility: carbon steel or zinc-plated fixings against a coated or galvalume sheet create a galvanic couple at every fixing point, and those points are precisely where water sits. Use stainless steel or aluminium in coastal and corrosive environments, hot-dip galvanised fixings inland. Second, cut edges: pre-drill rather than site-drill, because site drilling destroys the coating and leaves bare metal exposed at the fastener hole. Where cutting is unavoidable, specify cut-edge protection and seal it.
We supply coils with seaworthy packing, steel pallets and edge protection, and can arrange third-party inspection of the coating and packaging before loading. Full coating weight and surface treatment details appear on the mill certificate — see how to read an MTC.
For most Middle East projects, galvanized steel coil at Z275 with a high durability polyester or PVDF coating in a light colour is the right specification. The environment is hot and arid with intense UV, so the coating system is the deciding factor rather than the base metal — a light colour reflects more solar radiation and keeps the roof surface temperature lower, which materially slows coating ageing. For coastal Gulf projects, galvalume at AZ150 with a 32 µm minimum DFT is the better choice, and for very long life on remote or hard-to-access buildings, aluminium is worth the cost difference.
For coastal and humid environments, yes. Galvalume's aluminium-zinc alloy protects the cut edge sacrificially in a way pure zinc does not, and it has roughly double the corrosion rate advantage in salt spray testing. For hot-arid and temperate inland environments, the two are broadly comparable and galvanized is usually cheaper. Galvalume does have one disadvantage: it cannot be painted after installation without the paint adhering poorly to the passivated surface, so if the project might need a colour change later, galvanized is the safer base.
For standard profiled roofing in most markets, 0.47 mm to 0.60 mm is typical, with the requirement set by span and design wind load rather than by material category. Heavier gauge is needed for long spans, high wind loads and roof lights. Where corrosion is the concern, a thicker base is not the answer — a 0.5 mm sheet with a proper coating system will outlast a 0.6 mm sheet with a thin one. Check the local building code wind loading, because that governs the gauge and the fixing specification together.
Light colours. In hot-arid conditions the roof surface can exceed 70°C in direct sun, and darker surfaces reach higher temperatures still. Coating systems are rated for UV exposure, but service life is a function of temperature as well as radiation, and a dark PVDF roof will age measurably faster than a light one. White and light grey RAL colours are the standard specification for desert projects for this reason.
Aluminium is the right answer for genuinely marine exposure — island resorts, coastal industrial plants, and buildings where repainting is impractical. It needs no coating system at all, so there is nothing to degrade and nothing to maintain. The cost premium over coated galvanized steel is real but the total life-cycle cost over a 25-year horizon is usually better in marine exposure, because coated steel in that environment typically needs recoating in year 10 to 15. For coastal but sheltered locations, coated galvalume is the more economical choice.
Use fixings compatible with the base metal and coating system — stainless steel or aluminium in coastal and corrosive environments, hot-dip galvanised fasteners inland. Using carbon steel or zinc-plated fixings with a coated or galvalume sheet creates a galvanic couple at every fixing point, and those points are exactly where the water sits. Seal cut edges of the base sheet and pre-drill rather than site-drill, because site drilling destroys the coating layer and leaves bare metal exposed.
Send grade, thickness, width, coating and quantity. We confirm mill availability and return a proforma with the applicable standard and delivery window — normally within one business day.