PPGI paint build-up and thickness: PE, HDP and PVDF explained

Pre-painted steel coil fails in one of two ways: the coating is too thin to survive the forming process, or it is thick enough to survive but too soft to survive the weather. Both failures start with a specification that quoted a colour number and a nominal thickness without defining the paint system. This guide sets out how paint build-up is specified, what each system actually delivers, and how to specify a PPGI coil that will still look good in five years.

The four coating systems compared

These are the systems a mill will normally offer, and the differences are not cosmetic — they determine the service life and the price:

Coating system Typical total DFT Cost position Suitable exposure Expected colour life Main limitation
PE — Polyester~16–22 µm totalStandard economyIndoor use, mild climates, short service life1–5 yearsColour retention degrades faster, chalk-prone
HDP — High Durability Polyester~24–30 µm totalMid-range, most specifiedCoastal, humid, moderate industrial8–15 yearsBetter colour retention and chalking resistance
PVDF — Polyvinylidene Fluoride~35–40 µm totalPremium, best colour retentionSevere coastal, desert UV, high-profile buildings15–25 yearsHighest cost, limited colour range, requires clean handling
HDPE — High Durability Polyester (2-coat)~32–38 µm totalPremium polyesterAggressive UV and industrial exposure12–20 yearsBetter than single-coat HDP at lower cost than PVDF

Nominal thickness vs total dry film thickness

This is the single most misunderstood item in pre-painted coil specifications, and it causes arguments at inspection more often than any other. Four terms have to be kept straight:

Term What it means Why it matters
Nominal thicknessThe coating system thickness quoted in the system nameWhat the mill is paid to apply
Total dry film thickness (DFT)Nominal thickness plus the base steel tolerance contributionWhat you should specify and what the certificate reports
Minimum DFTThe lowest acceptable measured valueThe number that decides acceptance or rejection
Paint build-up effectHow much the base steel tolerance adds to the coatingThicker substrate tolerance produces a heavier coat than nominal

The practical rule: specify a minimum total dry film thickness. If your specification only quotes the nominal system thickness, the mill has room to argue that it supplied exactly what was ordered even when the measured value sits below your real requirement.

The paint build-up effect, quantified

The coat is applied between two rolls set for a target gap. The base steel thickness varies within its own tolerance, so the wet film varies with it. On a 0.50 mm base with a ±0.05 mm tolerance, the measured total DFT varies by roughly 7 µm across the sheet. This is small in absolute terms and decisive in commercial terms when the specification carries a minimum DFT and the mill has targeted the nominal figure.

The practical consequence for a buyer is that you should specify the minimum total DFT, and you should accept that the mill will supply to that minimum rather than to the nominal. Any mill worth working with will state the paint build-up effect openly. We specify minimum DFT on all pre-painted coil orders for exactly this reason.

How to specify colour and gloss

  • Give a RAL or SSAB colour number. RAL is the European convention and the most widely specified for export orders.
  • State the gloss level explicitly — typically 30–40% for building sheet.
  • Request a physical colour sample for approval against the standard, not just a photo.
  • Where the project has a specific brand colour, specify a spectrophotometer reading.
  • State whether the reverse side is bare, oiled, or passivated and oiled.

One practical note on colour matching: a colour reference is only meaningful against a physical standard. Screen colour names vary between mills and even between offices. The mill will normally supply an approved sample from the actual production run, and that sample becomes the reference. Where the project carries a brand or architectural standard, a spectrophotometer reading is the only reliable specification.

Forming a pre-painted coil without cracking it

Pre-painted coil is designed to be formed after coating, but the coating has to be specified as formable. Two requirements matter: a bend test, which is part of the coating standard and confirms the coating does not crack under the specified bend radius, and a forming temperature range, because paint becomes brittle as it cools. Forming a coil below the specified temperature is the most common cause of coating cracks that appear weeks later at the customer's installation.

For reverse-side protection, specify oiled, passivated and oiled, or interleaf. Bare reverse sheets are for immediate processing only and will develop red rust within days in a humid climate.

A complete pre-painted coil specification

Put these six items together and the order is unambiguous to any mill:

  • Coating system (PE, HDP, HDPE or PVDF) with a minimum total DFT in µm.
  • Base material and coating: galvanized or galvalume, with the base coating weight specified.
  • Colour reference and gloss level.
  • Formability requirement including bend test and forming temperature range.
  • Surface treatment state on both faces.
  • Packaging: seaworthy wrapping, steel pallets, edge protection, fumigation marks where required.

With that specification, the mill cannot deliver something that will fail. For base material selection, see our galvanized versus galvalume comparison, and for the exposure logic behind the coating choice, see roofing material selection by climate.

Frequently asked questions

What is the difference between nominal paint thickness and total DFT?

Nominal thickness is the coating system thickness in its name — a 25 µm PE system means 25 µm of paint. Total dry film thickness adds the contribution of the base steel tolerance. Because the base steel is coated while it still carries its thickness variation, the same paint system applied to a base with a ±0.05 mm tolerance produces a visibly and measurably heavier coat at the thick end. This is why mills and buyers disagree about whether a coil meets a 25 µm minimum: one is measuring the paint, the other is measuring the system. Specify minimum total DFT and the ambiguity disappears.

Which paint system should I specify for a coastal project?

For coastal or marine-adjacent exposure, high durability polyester with a minimum total DFT of 32 µm, or PVDF at 35 µm if the colour must stay stable over fifteen years or more. Single-coat PE at 20 µm will chalk noticeably within two to three years in a salt-laden atmosphere and is not appropriate for this exposure class. Galvalume base under a HDP or PVDF system gives better corrosion resistance than galvanized base because the aluminium-zinc layer protects the cut edge and the paint protects the surface — the two mechanisms are complementary.

How do I specify a colour for a pre-painted coil?

Give a RAL or SSAB colour reference plus the gloss level (typically 30–40% gloss for building sheet). RAL is the European convention and is the most widely specified for export orders. A colour name without a number — "RAL 9010 white" is fine, "special white" is not — cannot be matched reliably. The mill will supply a colour sample for approval against a physical standard before production, and that sample is the contract reference. Where the project has a specific brand colour, use a spectrophotometer reading rather than a chip.

Can PPGI be formed after painting?

Yes, and it is routinely roll-formed into profiled sheet after coating. What matters is that the paint system is specified as formable — bend tests and reverse bending tests are part of the standard, and the paint must not crack. Specify the bend test requirement on the order. Forming at low temperature makes the coating brittle, so forming temperature is also worth specifying. Pre-painted coil is normally supplied passivated and oiled on the reverse so it does not scratch against itself in the coil.

What is the paint build-up effect and how much does it add?

The coating is applied by roll coater to a moving web, and the gap between the two rolls is set for a target thickness. The base steel thickness varies within its tolerance band, so the wet film laid down varies accordingly. In practice, on a 0.50 mm base with a ±0.05 mm tolerance, the measured total DFT varies by roughly 7 µm across the sheet. That is enough to move a coil from marginally above a 25 µm minimum to marginally below it, which is why the paint build-up effect has to be accounted for in the specification rather than discovered at inspection.

How do I specify PPGI so it survives both forming and weather?

Specify three things together and you will not have a problem: a coating system (PE, HDP, HDPE or PVDF) with a minimum total DFT, a colour reference with a gloss value, and a formability requirement including a bend test and a forming temperature range. Add the surface treatment state — bare, oiled, or passivated and oiled — and the reverse side protection if the coil will be stored in an open yard. That is a complete specification, and it removes the two most common failure causes: coating that cracks at the roll former, and colour that fades because the wrong system was specified for the UV load.

Need help specifying your material?

Send grade, thickness, width, coating and quantity. We confirm mill availability and return a proforma with the applicable standard and delivery window — normally within one business day.

Request a Quote